Online It certification exam–Pass4side

8. To avoid data loss, what must a successful backup management policy for the Software Communication Server 500 (SCS500) include?

A.regularly scheduled backups of voicemail files

B.a dedicated area created on the server hard disk

C.unlimited storage to prevent older records from being overwritten

D.a backup file storage location separate from the Software Communication System 500 (SCS500) server

Answer: D

 

9. When you create a scheduled backup, where is the backup archive stored?

A.on the management PC

B.on the network device designated during configuration of the backup

C.in a protected area of system memory

D.locally on the Software Communication System 500 (SCS500)

Answer: D

 

10. Which action is required to configure Hunt Group call scenarios for incoming received digits presented to the Software Communication System 500 (SCS500) system?

A.Configure user aliases.

B.Enter the digits from the provider of the digital trunk as the hunt group number.

C.Determine the call sequence for Hunt Group user extensions.

D.Specify a Hunt Group Fallback Destination.

Answer: B

 

11. Which statement describes the software version requirements for restoring backup files on the Software Communication System 500 (SCS500) Rls. 2.0?

A.Only version 1.0 and higher can be restored.

B.Before attempting to restore a file, ensure that you have created a dedicated area on the SCS500 hard drive.

C.You can restore files that were backed up using one Software Communication System (SCS) version to another version.

D.Restore archives must be consistent with the software version on the SCS500.A

Answer: D

 

12. If the Software Communication System 500 (SCS500) server fails and all information is lost, which restore method can you use?

A.Restoring using the automatic file archive feature on the SCS500

B.Restoring using the SCS500 system archive folder

C.Restoring from the backup folder on the SCS500

D.Restoring using backup file upload

Answer: D

More info from: http://www.pass4side.com/922-095.htm

 

1. You are deploying a Communication Server (CS) 1000E system with a CP-PM Call Server and the campus redundancy feature. It is mandatory that you configure the CP-PM Call Server side for the campus redundancy feature to operate properly. In which two locations is the Call Server side configured? (Choose two.)

A. the BIOS menu

B. the Installation menu

C. the CLI using LD 97 Superloop commands

D. the CLI using LD 117 CPU Location commands

Answer: AB

 

2. A customer has successfully installed a Media Gateway Controller (MGC) in a Communication Server (CS) 1000E system. The MGC has registered with the Call Server.

 

Which is displayed on the MGC LED display to confirm successful registration?

A. The MGC display will read PASS

B. The MGC display will read OAD

C. The MGC display will read exxx ( E000).

D. The MGC display will show Superloop and Shelf of MG 1000E (4 0).

Answer: D

 

3. A customer is implementing a Communication Server (CS) 1000 Rls.5.0 Communication Server 1000E High Availability (HA) system. The customer wants to know if there are any special package requirements beyond the HA Package needed for the system. Which two software packages are mandatory when deploying a CS 1000E HA system? (Choose two.)

A. SBO - Branch Office Package 390

B. SOFTSWITCH - Soft Switch Package 402

C. IPMG - Media Gateway 1000E Package 403

D. SIP - SIP Gateway and Converged Desktop Package 406

Answer: BC

 

4. A customer is commissioning a Communication Server (CS) 1000E Rls. 5.0 system with Package 403 (Softswitch) and 402 (IPMG). The CP-PM Call Server software has been installed successfully, and now the customer is provisioning the Media Gateway Tone and Conference Loops for the Media Gateway Controller. Which switch overlay and prompt should the customer use to configure the Media Gateway TDS loop?

A. LD 17, XCT

B. LD 17, VXCT

C. LD 97, SUPT

D. LD 17, MGTDS

Answer: D

 

5. A customer is installing a Media Gateway Controller (MGC) in a Communication Server (CS) 1000E system. The customer is connected to SDI 0 of the MGC to access the configuration menu. No IP information exists for the MGC.

How does the customer get to the mgcsetup menu to configure the MGC?

A. Type mgcsetup on the screen.

B. No action required. The MGC will boot directly into the setup menu.

C. The prompt press any key to stop auto-boot and enter mgcsetup appears.

D. Enter a shell command. <CTRL>O<CTRL>A<CTRL>M, provide OAM username and password to access OAM shell.

Answer: B

More
1. The Branch Office platform includes a Media Gateway (MG) 1000B Core connected to a Communication Server 1000 Rls. 5.0 system at the main office over a LAN or a WAN. This configuration enables a secondary location to centralize the call processing of its IP-based communication network. Which statement is a true about the deployment of the MG 1000B?
A. It must be distributed in pairs.
B. It can be configured for survivability.
C. It can be distributed across a multiple building IP network.
D. It must be co-located with the Call Servers within a building.
Answer: C

2. In a Communication Server (CS) 1000 Rls. 5.0 Branch Office solution, which hardware component is required to host the Network Routing Service (NRS) software?
A. Call Server
B. Signaling Server
C. MRV Terminal Server
D. Media Gateway Controller (MGC)
Answer: B

3. When implementing a Communication Server (CS) 1000 Rls. 5.0 Branch Office solution, which hardware component is required to control call processing and provide the system memory required to store operating software and customer data?
A. SSC card
B. shared media hub
C. CP-PM Call Server
D. MRV Terminal Server
Answer: C

4. A customer is implementing a Communication Server (CS) 1000 Rls. 5.0 Branch Office solution. The customer wants to know if there are any special package requirements beyond the base CS 1000 Rls. 5.0 software? Which software package is mandatory when deploying a CS 1000 Rls. 5.0 Branch Office?
A. Branch Media Gateway package 390
B. Network Signaling (NSIG) package 37
C. Network Alternate Route Selection (NARS) package 58
D. SIP Gateway and Converged Desktop (SIP) package 406
Answer: A

5. A customer recently deployed a Communication Server (CS) 1000 Rls. 5.0 Branch Office solution. When examining the Call Server database of the main office, you observe that the bandwidth management zone created for the Branch Office on the main office is the same number as the zone created on the Branch Office. Which programming change will you recommend?
A. Add a new bandwidth management zone, zone 0, on the main office.
B. Make no changes to the main office or branch office zone numbering scheme.
C. Change the zone number on the main office to prevent potential conflicts with the branch office.
D. Change the zone number on the branch office to prevent potential conflicts with the main office.
Answer: B

The Oracle Certification Program is also valuable to hiring managers who want to distinguish among candidates for critical IT positions. For companies that send employees for annual IT training, certification ensures a return on the training investment by validating the knowledge and understanding gained during training sessions. Companies can also combine certification with an employee development program to enhance employee loyalty and performance on the job. Hiring certified professionals has a direct impact on a company’s success, as the following conclusions from research by International Data Corporation4 suggest: